Warbird Information Exchange

DISCLAIMER: The views expressed on this site are the responsibility of the poster and do not reflect the views of the management.
It is currently Sat May 10, 2025 6:08 am

All times are UTC - 5 hours


Classic Wings Magazine WWII Naval Aviation Research Pacific Luftwaffe Resource Center
When Hollywood Ruled The Skies - Volumes 1 through 4 by Bruce Oriss


Post new topic Reply to topic  [ 447 posts ]  Go to page Previous  1 ... 7, 8, 9, 10, 11, 12, 13 ... 30  Next
Author Message
 Post subject:
PostPosted: Mon Apr 13, 2009 6:53 pm 
Offline
User avatar

Joined: Thu Feb 28, 2008 6:46 am
Posts: 267
Location: Indianapolis, Indiana
Hello WIX people,

Another week's maintenance, and Hot Stuff is oh so close now. We actually thought we'd see that engine running this past Saturday, in fact; we had her serviced and ready, and went so far as to re-spot her into the wind for the run. But an unexpected leak in the fuel flow control valve--which was not a leaky thing last time we had a running engine on that side--caused us to belay that evolution.

Ach, the disappointment. But all in all, it was a good work day. We are so close now to completing the annual and having the plane back in the air. We need to get 'er done, too, because we have an engagement on the east coast in the middle of May. So you can expect to hear of some high-tempo maintenance happening the next couple weeks.

Image

Right there you see the cause of all the trouble this week. That's the fuel flow control valve. It determines where the engine gets its fuel--one of the two inboard forward tanks. "Normal" is the tank on the same side as the engine; "Cross-feed" is the one from the other side. It is not supposed to leak from the pulley shaft. Unfortunately, it does.

We expect that the trouble is in the shaft seal, a $25(!) o-ring. We'll pull that thing out of there next maintenance day and replace the seal, and hopefully that will move us beyond Static Display status, and back into the bomber pattern.

Right above the valve, by the way, is the big oil tank. There's a tank in each wheel well. If your engine locks up, that tank's got to come out and be thoroughly cleaned, to get rid of the metal chips. IndyJen has had all the experience of pulling that tank and reinstalling it as many times as she wishes to have. The thing weighs about sixty pounds, and is just as easy to get in and out of there as it looks.

It was a busy day out there, with lots to do, so let's move on to the maintenance report, shall we?

Image

That's our man John P., our marketing guy. He was able to make a rare appearance out on the maintenance ramp, and some of the pics that follow are courtesy of him. Early in the day, I had him helping me install the pre-oil connection. We have solved the pre-oiling question we had some while back, and have a good efficient means for doing it now.

Image

Preparing to climb up and inspect this wonderful device is our AI, George. He came out for the engine run, and as usual, kept a keen eye on all that transpired.

Image

You can see the connection there, aft of the air-oil separator can. It's a check valve that's connected to the port called out in the manual. Easy to get to, no mess, entirely satisfactory.

Image

There was plenty going on in both nacelles, as you can see. With the new left engine so close to being done, we've put a team onto cleaning up and preparing the right engine, too. Its annual is progressing, a big part of which is battling the annual birds. They think an R-2800 is the finest nesting site available, and they are very insistent about it. Bob the new guy and both Riches were cleaning it out. They also removed the cowl flaps and undid all the spark plug wires, and were ready to start pulling plugs when we had to make 'em stop work.

In the nose most of the morning was PJ, finishing up some inspections of the electrical j-boxes in there. The cockpit is all together now, too, thanks to Johnny Gearpin's fine sheet-metal fixes.

Image

There's Machine Shop Gaylon, helping do the final rigging of the prop controls. The control run to the prop governor had a bad pulley, which made terrible noises whenever one caused it to move. This was only a problem when the engine wasn't running, because otherwise, you couldn't hear the noises. But this isn't something to leave alone. Oddly, the one-inch pulleys in that bracket are a unique Lockheed part, and are not all that easy to come by. But you can still get them, albeit with difficulty. That's all fixed now and good to go.

Image

How many mechanics does it take to put oil in a Harpoon? Two, per our usual practice, but this does not preclude a crowd of kibitzers, especially when we've not had to service the plane in a good long while. I've got a couple of our prospective crew chiefs up there doing some hands-on training. The main important thing: when you replace the oil-tank cap, you must feel it lock into the detent. If it doesn't, the tank won't vent, and bad things follow, not least of which is a tremendous mess when the tank over-pressurizes. We serviced fifteen gallons in the twenty-gallon tank.

And then we used that fine pre-oil connection to put about another five gallons into the engine.

Image

The procedure involves pumping oil into the engine's unused oil-pressure gauge connection (there's one on each side of the engine case, but you only use the inboard one) while pulling the prop through. The main oil sump plug is pulled, and when the scavenge pump sends clean oil out of the sump, pre-oiling is complete.

As you can see, we had no shortage of enthusiastic prop-pullers.

Image

With the engine oiled up, battery installed, battery cart available, and the cowling installed, it was time to point the plane into the wind. Note that we left the accessory section uncowled, the better to spot any leaks.

Image

And there we are, WIXers: all set. The crew at this point has adjourned into the office for a briefing, and when we come out, it's time to run.

First thing we did was hook up the battery cart and test each pump: good to go. Fixed one minor leak in a matter of minutes, and so let's move fuel into the left inboard for the run ... and what's that fuel, dripping from the gear well?

Ah drat it. We can't run with the main fuel valve dribbling fuel, especially as it sits about a foot from the exhaust. So that's as far as we got.

But you know, as much as I wanted to hear that engine run, it wasn't that big of a disappointment. We had a fine day's work, and we can plainly see the light at the end of the tunnel now.

We'll fix the valve this week, and we will also have our power cart repaired and running again by the time we're ready to run--which won't be until a week from Saturday, due to lack of flight crew. I expect that we'll run it, set it up, and then look very closely at a shakedown-flight schedule to follow closely behind.

Image

Till next time,

_________________
IndyJen

------------------------------

Support "Hot Stuff"
Lockheed PV-2 Harpoon of the
American Military Heritage Foundation
http://www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 19, 2009 6:40 pm 
Offline
User avatar

Joined: Thu Feb 28, 2008 6:46 am
Posts: 267
Location: Indianapolis, Indiana
Hello WIXers,

Another week gone, and work progresses on Hot Stuff. Having not the necessary cockpit crew, there was no plan to run engines this week, so although we pressed ahead with the preparations, there was not the usual level of frenzy about it.

As you may recall, last week's intended run of the new engine was aborted due to an unexpected leak in the left fuel flow control valve. So first thing on the program was that item, 'cause we're not running nor flying with fuel dripping out a foot from the exhaust.

Image

There it is, on the back-side of the firewall. The valve, a 3-way Aero Supply poppet type, mounts on a bracket, and its operating pulley-drum mounts on another bracket attached to the face of the valve. Cotter pins keep the fork on the end of the valve shaft engaged with a corresponding fitting on the pulley drum.

All of this is located in a not-quite inaccessible position, just at the end of one's reach. For some bizarre reason, they didn't design in nutplates for the mounting bolts, so there's a lot of standing-on-one-leg-while-holding-your-mouth-just-right invovled in getting the thing out of there. You need two-and-a-half hands about half the time, but there's only room for one-and-a-half hands most of the time. It is what it is.

Image

There's PJ, taking a turn at trying to get the hoses disconnected. From this image, you can get some idea of what kind of room there is to work with, there in the wheel well. The book actually insists that this valve is to be removed from outside the nacelle, via an access panel, and that's what we're looking through, here. Well, we generally go by the book, but I have to say, we and the book just weren't seeing eye to eye this time.

Image

There's how we actually did it--you just couldn't use the necessary two hands on the thing from outside, at least not without removing the exhaust, and we didn't want to do that.

In the end, the thing came out without an undue level of difficulty, and the vocabulary wasn't any more creative than usual, except when the fuel came gushing out upon us. We drained the tank beforehand, but there's still fuel in the lines, and IndyJen and PJ both were wearing Eau de 100LL well before the end of the process.

Image

There it is, ready to pull the shaft and install new seals. These o-rings cost 25 bucks each, but the main thing is that they're still available at all.

Meanwhile, we had other teams doing other things as well: there were 36 plugs to remove, clean, gap, and reinstall, and a compression check to be done on the right engine, for starters.

Image

There's Machine Shop Gaylon and Rich no. 1 (the Official Dad of IndyJen), who did the bulk of the engine work, along with Rich no. 2 and Hot Rod Steve. The latter two guys were primarily working on rebuilding the ground power cart, though--more on that later.

A balky sparkplug grit-blaster slowed things down for a while, but the boys were able to get that thing back on line.

Image

There's PJ and Rich no. 1, with the handy spark-plug-sorter. We also use that item for keeping track of pushrods when necessary. I don't know if the plugs were coming out or going in at that point, but no matter--it was a good day all day, a fine day to be outside with an old warbird.

Image

There's a view of Rich no. 2, Hot Rod Steve, and the power-cart engine. It started making a terrible racket a couple weeks ago, and tearing it down revealed two busted pistons. Replacement parts arrived late last week, and Rich and Steve tore right into it, breaking off on occassion to lend a hand with the other projects. We expect to have it working again in time for next weekend's engine runs.

Preparing for the compression check on No. 2, we pre-oiled to make sure those bearings weren't dry. Both engines now have the pre-oil connection I described last week; it is a handy device, and having a check valve as a connection point works very well at minimizing the mess.

So, there we were, pulling the prop through while pumping in the oil, when up walks a fellow in a PV-2 hat. Now, we're the only people round here who wear PV-2 hats, so who was this guy? Well, when he walked up and said "you must be IndyJen," it became clear: it's Gary Hilton!

Image

And there's the smiling face of our man right there. Gary hopped right into the prop-pulling parade (no strain, with only one plug installed in each cylinder), and hung out chatting for a while. There might have been a compression check for him to witness, too, except for the unexpected problem: pulling the engine through turned the hydraulic pump, which in turn pressurized the line on that side, which did not formerly leak. But now it does.

Our first clue was the stream of red liquid dribbling from the wing root. The lines run through the hollow inboard leading edge to the fuselage, where there's a coupling. Well pull that leading edge during the midweek maintenance days, and figure out whether it's just gotten loose, or if a replacement line is needed. Either way, it ought to be ready by the weekend.

It's just one of those things that happens when your plane doesn't run for a long time. No use getting worked up about it. But we did have to abandon the compression check, because we didn't want to fill up the wing with hydraulic fluid, now did we?

So that's the story of this week. All in all, it was a good day's work. Next time, we'll hopefully have some reports of spinny, smoky, noisy things for you!

Till next time,

_________________
IndyJen

------------------------------

Support "Hot Stuff"
Lockheed PV-2 Harpoon of the
American Military Heritage Foundation
http://www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Thu Apr 23, 2009 5:29 am 
Offline
User avatar

Joined: Thu Feb 28, 2008 6:46 am
Posts: 267
Location: Indianapolis, Indiana
Time for a mid-week update:

The Wednesday Afternoon Maintenance Crew did a good day's work yesterday, and it look like we're back on track for a weekend engine run. No pictures this time, unfortunately, but here's the run-down:

The hydraulic leak has been found and fixed. A connection was loose on the co-pilot's side of the plumbing run. The right inboard leading edge was pulled in the course of tracking down the problem, and the crew pulled the other side's inboard leading edge while they were at it, just to make sure there were no surprises lurking there as well. PJ and Scotty took care of business in that area.

The other big problem--the leaky fuel flow control valve, which we pulled last Saturday--was disassembled and new shaft seals installed by Machine Shop Gaylon. The new o-rings, which cost 25 bucks each, look nice and round and fat. The old o-rings looked flat and square, so there's your problem, right there. We'll put that valve back in place first thing Saturday morning.

Glen fabricated a couple new lines for the emergency hydraulic system as well, a project that's been on his mind for while.

Rich no. 2 and Hot Rod Steve wrapped up the reassembly of the ground power cart engine. Rich and Steve will get that engine back in place, and we ought to have the cart available for Saturday afternoon's business.

So, WIXers, there you go. Some of our folks are going back out there this afternoon to continue attacking some loose ends--our friendly neighborhood sheet-metal man, Sheet Metal Dennis, is coming to finish installing some patches in a tail-section bulkhead, and yet more annual items will be getting checked off meanwhile. These latest unexpected problems set us back, schedule-wise, but we're about caught back up, and that's good.

More news, with pics, at the weekend,

_________________
IndyJen

------------------------------

Support "Hot Stuff"
Lockheed PV-2 Harpoon of the
American Military Heritage Foundation
http://www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Thu Apr 23, 2009 6:05 am 
Offline
Long Time Member
Long Time Member
User avatar

Joined: Tue May 11, 2004 5:42 pm
Posts: 6884
Location: The Goldfields, Victoria, Australia
IndyJen wrote:
The hydraulic leak has been found and fixed. A connection was loose on the co-pilot's side of the plumbing run.

IndyJen forgot to add: "The co-pilot has been dragged from where he was hiding and shot. A trainee replacement is under way, and has entered the 'softening' process with the baseball bats. This problem will not reoccur." :D

Great stuff (not what I said, what you said) IndyJen, keep us posted.

You have a reply PM, btw.

_________________
James K

"Switch on the underwater landing lights"
Emilio Largo, Thunderball.

www.VintageAeroWriter.com


Top
 Profile  
 
 Post subject:
PostPosted: Sat Apr 25, 2009 10:10 pm 
Offline
User avatar

Joined: Thu Feb 28, 2008 6:46 am
Posts: 267
Location: Indianapolis, Indiana
Just a quick update, WIXers ...

It's 11:20, and I've only been home about 15 minutes. Exhausted, filthy, and happy as hell, but no time nor energy for the usual long-winded, photo-filled post just yet. But I still have to tell the good news.

Hot Stuff's a twin-engined airplane again, with two engines that run, and at the same time, too. She looks and sounds good with both fans turning, let me tell you.

Now I am going to go have a bath, and clean up, and crawl into bed, and sleep the sleep of the just. It was a hell of a long work day to get to this point, and I am just wiped out--like the rest of the crew. There'll be the full-blown post tomorrow, with photos and all, but there's no time nor energy for that just now. But it's been a long and difficult process, getting to this point, and you know I couldn't wait to tell.

Regards,

_________________
IndyJen

------------------------------

Support "Hot Stuff"
Lockheed PV-2 Harpoon of the
American Military Heritage Foundation
http://www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 26, 2009 4:09 pm 
Offline
User avatar

Joined: Tue Dec 27, 2005 10:51 am
Posts: 137
Location: BHX. UK
Well done to you all! :P

_________________
Those that can do,those that can't be bothered,TALK about it.
Volunteer with Classic Flight and a member of Beech Restorations team.
http://beechrestorations.wordpress.com/about-us/
http://www.classicflight.com.


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 26, 2009 9:04 pm 
Offline
User avatar

Joined: Thu Feb 28, 2008 6:46 am
Posts: 267
Location: Indianapolis, Indiana
Hello WIXers,

According to the dates on my Photobucket files, it was twenty-three weeks ago that I started this thread, with the promise that at the end, we'd have airworthy airplane with two running engines to show for it.

That day is finally here.

Image

Boy, is it nice to type those words, and post that picture. It's been a long, and difficult road, getting to this point with ol' Hot Stuff, but here we are. I am so proud of our little maintenance crew. There's been a lot of adversity to overcome, but our guys and girls stepped up and did what needed to be done, every time. Even when it took a twelve-hour workday that left 'em staggering off the ramp in exhaustion--which pretty well describes yesterday's effort--there they were, making it happen. Words just cannot express the admiration I feel for all these selfless, dedicated folks.

Both engines ran well and sounded fine, but I have to tell you, that new one is a peach. Anderson Airmotive did a tremendous job on that thing, from all appearances. Started so easy, barely threw so much as a drop of oil nor a puff of smoke. We have a couple glitches to address on the plane--it looks like our battery has finally given up the ghost, and will need to be replaced, and the LH primer solenoid wants some tinkering--but really, we're into routine-maintenance land from here on out, it sure looks like. That kind of stuff is normal life in Harpoon Land. That battery, though--there's an expense we really didn't need right now. But you've got to have a battery that will deliver electrons, and ours no longer wishes to do so. They don't last forever, after all.

There was a lot happening, leading up to the climactic engine runs, and plenty that bears description. So let's move on to the tale of the day, shall we?

It was an early start, because there was so much to do. I'm often leery of setting too aggressive a schedule, of making the goals too ambitious, because you know how repeatedly missing the mark can wear down peoples' morale. This means that I sometimes do more to put the brakes on than to get people going, which can be frustrating for some, I know--we have no shortage of go-getters in this group. But this time, there was a big plateful of stuff needing to be done, and no mistake, and the go-getters had all they could handle, and then some.

First thing: get that right engine put back together and ready to run. Plugs, plug wires, cowl flaps, and myriad small details.

Image

There's the right-engine crew: Machine Shop Gaylon led that effort. Hot Rod Steve is up there helping install cowl flaps, while Rich No. 1 (the Official Dad of IndyJen) is underneath, installing plugs and hooking up plug leads.

Image

There's the old man again, who I'll tell you, in sports parlance, there's a guy who just left it all on the field. One of the first to come, one of the last to leave, and he was dragging when he left, too, but he got it done. One of the great things about this latest engine change is that Dad's really gotten involved with the group. He's become one of the regulars, and you can count on him to be there week in and week out. He's become a really valuable part of the maintenance force. I just purely love having him out there.

In the background of that first pic is Rich No. 2, who put in a maximum effort on the ground power cart, but still would jump up at a moment's notice to lend a hand anywhere else he was needed.

Image

There's the cart, which was a project Rich no. 2 and Hot Rod Steve have primarily been working on. They have sunk a huge effort and considerable cash getting that thing going again, with only a couple weeks to do it, too. Another example of big effort, great dedication, and all in a very quiet way, too--no fanfare with these guys, although if I had my way, there'd be a parade for 'em.

Scotty there in the pic, who's one of our co-pilots, flies international freight, and can understandably only come out when he's in the western hemisphere, but he has a big impact when he's there.

Image

There he is, working on settling up matters in the LH leading edge. We pulled both the inboard LE's to check control runs and fluid connections. Scotty has a good eye for catching inspection discrepancies, and did a good conscientious job. He also joined PJ and me in the wheel well, were we were having a heck of a time getting hoses reconnected to the repaired fuel flow control valve. Scotty came, saw, and conquered, with both muscle and ingenuity: you're the man, Scotty!

Image

You can just see PJ's legs, there, as she's perched on the main wheel, working on that valve. She's a small package, but feisty, and the very soul of dedication when it comes to this plane--a fount of historical knowledge, and puts in more wrench-turning hours than anyone else, hands down. I think I've previously mentioned that we often call on her when we need someone to get into tiny spaces. She's all business, that one, and there's no quit in her.

Image

There's Long Tall Glen, another one I can't see how we could do without. He's one of two guys who were one day from their PV-2 type rating checkride when the old left engine crapped out. A homebuilder--RV-8--and extremely knowledgeable guy, possessed of a real craftsman's ethic. He's finishing the sheetmetal work in the tail, there, a project that's been ongoing for months.

The other guy who was 24 hours from type rating was Barnstormer Joe, another big heart in a small package. He was on the road flying, and his wife, President Penny, was out of town to meet up with him. Penny has been a miracle worker. We would have been on the auction block long since without her. If you see Hot Stuff flying through your skies in days to come, you may know that Penny had as much to do with that as anyone. You'll see those two pictured next week, most likely; they ought to be back by then.

Image

Meanwhile, back in the office, is Roy the electrical guru and John P., our marketing guy. A number of these pics are courtesy of John, and Roy is a man who's really good to have on the team, as he has major-league skills when it comes to electrical and electronic work. He kept B-52 wiring up to snuff in days gone by.

Image

There's Hot Rod Steve and Machine Shop Gaylon during a rare break. These were few and brief on Saturday.

Image

Finally, as the day wore on, we got to the point where a certain person, who writes these missives, ceased despairing of ever starting an engine, because one team after another began reporting "ready to go." Here's the left side being buttoned up, because we've transferred fuel into the left inboard and run pumps, and by golly, that flow control valve didn't leak a drop.

Pull 'em through, and preoil both side, and finally, around 5:30 p.m., it's time. We chose to start No. 2 first.

Image

There she is, lighting off. A smoky start; the engine had some oil in the collector ring after the pull-through. It's not unusual, after it's sat for a while without running, for the initial start to make Mount Comfort Airport IFR for a few minutes! That'll blow a lot of oil onto the gear doors and such, too. Subsequent starts were clean and not-smoky.

After the temps came up and the oil pressure dropped, and No. 2 was idling good, came the long-awaited First Start of the new No. 1 engine. No smoke, maybe a couple drops of oil, which among R-2800's, is the same as "Operating Room Clean." Well I never. It was a beautiful thing, let me tell you.

Image

There they are, both fans turning. That's PJ in the escape hatch, the normal position for our crew chiefs (3rd crew member) when on the ground. It was a warm day, and that was probably the most comfortable seat in the house. I bet her thumbs got tired from signaling me "thumbs up" throughout this evolution. Mine sure were, from returning the signals.

Image

There's a look at our ground-crew configuration for the run: me out front, communicating with the crew; observers/fire guards at each wingtip, keeping an eye out for leaks, smoke, flames, and other dire occurrences, none of which ever transpired. Rich No. 2 ran the power cart, and Rich No. 1 and John P. took photos and movies. I'll post up links to the movies once I've gotten them from Dad. I can hardly wait.

Image

At the end of the day--the bitter end of a totally not-bitter day--there were only three. It's 10:30 p.m. or so in this pic, and we exhausted ones are just sitting out on the calm quiet ramp, drinking our celebratory beverages, looking at a real live airworthy Harpoon. We were so bone-tired, it was a quiet celebration, but the engines had already made all the noise that needed to be made.

A good day.

Till next time,

_________________
IndyJen

------------------------------

Support "Hot Stuff"
Lockheed PV-2 Harpoon of the
American Military Heritage Foundation
http://www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 26, 2009 9:35 pm 
Offline

Joined: Tue Jul 22, 2008 4:43 pm
Posts: 77
Location: Heber, UT
To all of your crew and organization....GREAT JOB!!! :D :wink: Look forward to airborne pics...once again WELL DONE!!
Dave
PV-2 "AW"


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 26, 2009 10:08 pm 
Offline

Joined: Thu Feb 05, 2009 2:48 pm
Posts: 230
Location: minnesota lakes
Working on pond's airplanes in the 80's and 90's you have your'e up's and downs..this and that's but the end result is the most beautiful sounds and smells that we can ever have..You all have done a great job with nasty weather. may you fly with the wind.

_________________
PAPPY ch-46 phrog,endangerd species 40 years and still flying


Top
 Profile  
 
 Post subject:
PostPosted: Sun Apr 26, 2009 11:11 pm 
Offline
Long Time Member
Long Time Member
User avatar

Joined: Tue May 11, 2004 5:42 pm
Posts: 6884
Location: The Goldfields, Victoria, Australia
Congratulations. Great stuff, and hot too...

_________________
James K

"Switch on the underwater landing lights"
Emilio Largo, Thunderball.

www.VintageAeroWriter.com


Top
 Profile  
 
 Post subject:
PostPosted: Mon Apr 27, 2009 3:05 am 
Offline
3000+ Post Club
3000+ Post Club

Joined: Thu Dec 21, 2006 8:32 am
Posts: 4324
Location: Battle Creek, MI
FAN FREAKIN TASTIC!

Great work, folks!

SN


Top
 Profile  
 
 Post subject:
PostPosted: Mon Apr 27, 2009 4:13 am 
Offline
User avatar

Joined: Fri Jun 24, 2005 7:59 am
Posts: 500
Location: Central Indiana
Thanks to all of the WIXers who have journied along with us over the last 5 or 6 months and for your kind words.
Dave, airborn photos will indeed be next!


PJ
PV-2 Harpoon "Hot Stuff"
www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Mon Apr 27, 2009 9:10 am 
Offline
3000+ Post Club
3000+ Post Club
User avatar

Joined: Fri Mar 02, 2007 6:52 pm
Posts: 3410
Location: Wichita Falls, Texas, USA
Great job guys! Hope you're able to get her down in the Texas area one day. Would be great to see her at Midland even. :)


Top
 Profile  
 
 Post subject:
PostPosted: Mon Apr 27, 2009 9:22 am 
Offline
User avatar

Joined: Fri Jun 24, 2005 7:59 am
Posts: 500
Location: Central Indiana
Midland would be great! We enjoyed being able to help out Ole 927 and flying on her last September and it would be nice to fly down and see everyone.

PJ
PV-2 Harpoon "Hot Stuff"
www.amhf.org


Top
 Profile  
 
 Post subject:
PostPosted: Mon Apr 27, 2009 9:49 am 
Offline
2000+ Post Club
2000+ Post Club
User avatar

Joined: Sat Oct 04, 2008 6:57 pm
Posts: 2716
Location: St Petersburg FL, USA
Well Done to All!!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 447 posts ]  Go to page Previous  1 ... 7, 8, 9, 10, 11, 12, 13 ... 30  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Google [Bot] and 296 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group