Warbird Information Exchange

DISCLAIMER: The views expressed on this site are the responsibility of the poster and do not reflect the views of the management.
It is currently Tue Jul 08, 2025 5:16 am

View unanswered posts | View active topics


Board index » General Discussion » The WIX Hangar

All times are UTC - 5 hours


Classic Wings Magazine WWII Naval Aviation Research Pacific Luftwaffe Resource Center
When Hollywood Ruled The Skies - Volumes 1 through 4 by Bruce Oriss


Post new topic Reply to topic  Page 1 of 1
  [ 14 posts ] 
  Previous topic | Next topic 
Author Message
Michel Lemieux
PostPosted: Fri Oct 26, 2007 12:29 pm 
Offline
2000+ Post Club
2000+ Post Club
User avatar

Joined: Fri Apr 30, 2004 8:11 am
Posts: 2392
Location: Montreal, Quebec, Canada
Flying Bulls P-38 at Ezell

What is that material they are using for stamping ?

Seems strong enough for small runs & easier to machine also.

Just curious....as always.

http://www.ezellaviation.com/Past%20Pages/P38/header.html

Image


Image

Image

Image
Top
 Profile  
 
Ztex
 Post subject:
PostPosted: Fri Oct 26, 2007 2:23 pm 
Offline
Senior Moderator
User avatar

Joined: Thu Jun 15, 2006 12:22 am
Posts: 3875
Location: DFW Texas
Looks like it might be UHMW (ultra high molecular weight polyethylene)
Just a guess

_________________
Zane Adams
There I was at 20,000 ft, upside down and out of ammunition.
_______________________________________________________________________________
Join us for the Texas Warbird Report on WarbirdRadio.com!
Image http://www.facebook.com/WarbirdRadio
Listen at http://www.warbirdradio.com
Top
 Profile  
 
RMAllnutt
 Post subject:
PostPosted: Fri Oct 26, 2007 2:39 pm 
Offline
1000+ Posts!
1000+ Posts!
User avatar

Joined: Fri Apr 30, 2004 9:52 am
Posts: 1949
Location: Virginia, USA
What I am trying to understand is how they got the wrinkles out in this piece. If you look at the complete set of photos, it is an amazing bit of labor. I am simply stunned at the craftsmanship of these guys. I don't think I have seen its equal, other than perhaps the guys at Precision in Australia.

Cheers,
Richard

_________________
Richard Mallory Allnutt - Photography - http://www.rmallnutt.com
Top
 Profile  
 
MX304
 Post subject:
PostPosted: Fri Oct 26, 2007 4:19 pm 
Offline

Joined: Fri Jul 08, 2005 7:50 pm
Posts: 701
Location: Dallas / Midland TX
That could also be Delron (sp?) they are using to make the dies.
Top
 Profile  
 
daveymac82c
 Post subject:
PostPosted: Fri Oct 26, 2007 4:43 pm 
Offline
2000+ Post Club
2000+ Post Club
User avatar

Joined: Sat Nov 25, 2006 9:18 pm
Posts: 2275
Location: Vancouver, BC
Quite awesome stuff! I can't wait to see it back in the air.

-David
Top
 Profile  
 
Paul Draper
 Post subject:
PostPosted: Fri Oct 26, 2007 6:17 pm 
Offline
User avatar

Joined: Fri Apr 30, 2004 12:17 pm
Posts: 125
It looks like it could be "Renboard". I've had dies made from renboard in the past to make dies for short run stampings. Works pretty good if you're stamping aluminum or other soft metals.
Top
 Profile  
 
Bill Greenwood
 Post subject: smart
PostPosted: Fri Oct 26, 2007 6:39 pm 
Offline
Probationary Member

Joined: Wed Jun 21, 2006 7:53 pm
Posts: 3803
Location: Aspen, CO
Some of those old country boys do know a new trick or two! I was there this summer and saw how much work was going into the P-38, because it was complex and a lot had to be made from scratch.

_________________
Bill Greenwood
Spitfire N308WK
Top
 Profile  
 
bdk
 Post subject:
PostPosted: Fri Oct 26, 2007 8:42 pm 
Offline
Been here a long time
Been here a long time

Joined: Sun May 02, 2004 1:16 am
Posts: 11324
RMAllnutt wrote:
What I am trying to understand is how they got the wrinkles out in this piece.
I think they are hydro-forming the basic (rough) shape and then knocking the wrinkles down/out with a wooden block and a hammer as shown in this photo:

Image

As they knock down the wrinkles they can hydro-form more. They just go little by little.
Top
 Profile  
 
ezellaviation
PostPosted: Fri Oct 26, 2007 10:04 pm 
Regarding the header tank molds, the material is a high density, machinable plastic. This was the first time we have used it for this application.

Thank you for the kind words!

Ashley
Top
  
 
Lynn Allen
PostPosted: Sat Oct 27, 2007 10:44 pm 
Offline
3000+ Post Club
3000+ Post Club
User avatar

Joined: Fri May 07, 2004 10:10 pm
Posts: 4409
Location: Maypearl, Texas
ezellaviation wrote:
Regarding the header tank molds, the material is a high density, machinable plastic. This was the first time we have used it for this application.

Thank you for the kind words!

Ashley


Ashley,

Hello and welcome to the board. Keep up updates coming....

Lynn
Top
 Profile  
 
6trn4brn
 Post subject:
PostPosted: Sun Oct 28, 2007 5:25 am 
Offline

Joined: Mon Dec 11, 2006 4:50 pm
Posts: 743
Location: Blue Hills of Virginia
Sure hope the hand in the first photo is not going after the chip wrapped around that drill! Made that mistake ONCE myself :cry:

I think Delron might be a bit too soft for molding metal aroud.

_________________
Earn my respect and never lose it.
Demand my respect and never gain it. -Me

...just another plane dreamer.
Top
 Profile  
 
Michel Lemieux
 Post subject: On the subject of......
PostPosted: Mon Oct 29, 2007 2:35 pm 
Offline
2000+ Post Club
2000+ Post Club
User avatar

Joined: Fri Apr 30, 2004 8:11 am
Posts: 2392
Location: Montreal, Quebec, Canada
On the subject of...... :idea:

Is the original part scanned in 3D as a base or does someone goes through the necessary pains of manual mesurements to CAD drawing from scratch :?:

Outstanding work in any case.

Michel.
Top
 Profile  
 
ezellaviation
PostPosted: Mon Oct 29, 2007 5:34 pm 
Michel Lemieux wrote:
On the subject of...... :idea:

Is the original part scanned in 3D as a base or does someone goes through the necessary pains of manual mesurements to CAD drawing from scratch :?:

Outstanding work in any case.

Michel.


We have the tanks that came off the project, but there was too much corrosion. No new ones were available (with no dents anyway) so we decided to fab some new ones.

The bungs were all manually machined on a Lathe using the originals for dimensions. The end caps were spun using a machined male mold.

Using the original tanks and original blueprints, I made a solid of the tank using Autodesk Inventor. I split the model into two halves and formed a base under each half making two male molds. From there, it goes to Gibbs Cam to program the tool paths for machining the part.

Ashley

BTW: Thanks Lynn- we are getting closer!
Top
  
 
Michel Lemieux
 Post subject: Tks for the info
PostPosted: Tue Oct 30, 2007 11:34 am 
Offline
2000+ Post Club
2000+ Post Club
User avatar

Joined: Fri Apr 30, 2004 8:11 am
Posts: 2392
Location: Montreal, Quebec, Canada
Tks for the info...and a late welcome :wink:

The cad part is also a lot of work.

Congrads one the amazing craftmanship displayed.

Michel.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 14 posts ] 

Board index » General Discussion » The WIX Hangar

All times are UTC - 5 hours


Who is online

Users browsing this forum: Google [Bot], Google Adsense [Bot] and 39 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB® Forum Software © phpBB Group