| Warbird Information Exchange https://www.warbirdinformationexchange.org/phpBB3/ |
|
| T-6G / Hoisting complete A/C / Thread-size hoisting ring?? https://www.warbirdinformationexchange.org/phpBB3/viewtopic.php?f=52&t=47908 |
Page 1 of 1 |
| Author: | chrisB [ Sun Nov 25, 2012 11:23 am ] |
| Post subject: | T-6G / Hoisting complete A/C / Thread-size hoisting ring?? |
Hello everybody, we are going to overhaul a T-6G in Germany and I hope you can help me out with some infos... The A/C is some hundred miles away right now and not that easy to access, we need to disassemble it for road transport to germany. Therefore we are building some hoisting equipment. Does anyone know the thread-size of the hoisting ring, that will be screwed in the wing middle section? (E-700 in the second picture) Thank you in advance! Chris  
|
|
| Author: | 51fixer [ Sun Nov 25, 2012 3:57 pm ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
The E-700 Lifting Eye has- 5/8"-18NF-3 Threads from the bottom to 5/8" up the shaft. 1/8" of transition from 5/8-18 threaded dia to 3/4" dia. 3/4" to 1 9/16" up the shaft the dia is 3/4" Starting at the 1 9/16" point there is a flange about 1 1/8" dia by 1/8" tall and then a ring 1/2' thick with an OD of 1 3/4" and an ID of 3/4". Above that is a large loop made from 1/2" dia bar 1 1/8"radius on the OD, 7/8"radius on the ID for the top and bottom circles of the loop with overall length of 4 1/4" top to bottom of the loop. The loop is made in 2 pcs and welded together installed in the eye of the threaded eyebolt discussed above. Good luck. We have lifted using a strap under the upper engine mounts where it attaches to the firewall. Look down this page- viewtopic.php?f=3&t=21830&start=1230 |
|
| Author: | Tiger moth [ Sun Nov 25, 2012 7:48 pm ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
Lance aircraft had the lifting rings when I bought mine. |
|
| Author: | chrisB [ Mon Nov 26, 2012 8:10 am ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
51fixer and Tiger moth, thank you very much for the helpful information! |
|
| Author: | C.6-60 [ Thu Nov 29, 2012 3:51 am ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
Hello Chris B. I came up with another part number for the lifting eyes. The Erection & Maintenance Handbook T.O. 1T-6C-2 revised 30 Nov 1956 Figure 41 - Loose Equiptment - shows Item 10 Hoist Fittings Part Number 36-55009 I hope this helps you if you are trying to order them. Vincent |
|
| Author: | chrisB [ Fri Dec 21, 2012 8:44 am ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
for everybody else interested in the hoisting rings, see the pic below (rings bought from Lance) 
|
|
| Author: | chrisB [ Fri Dec 21, 2012 8:51 am ] |
| Post subject: | Re: T-6G / Hoisting complete A/C / Thread-size hoisting ring |
And regarding the transport of the A/C to Germany, the link and pics of "51fixer" were very helpful, we also did not use the hoisting rings and instead used slings around the engine mount.  Road transport on the "autobahn"  Unloading, it just started to snow |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|