Warbird Information Exchange

DISCLAIMER: The views expressed on this site are the responsibility of the poster and do not reflect the views of the management.
It is currently Sat Jun 21, 2025 7:52 am

View unanswered posts | View active topics


Board index » General Discussion » The WIX Hangar

All times are UTC - 5 hours


Switch to mobile style
Classic Wings Magazine WWII Naval Aviation Research Pacific Luftwaffe Resource Center
When Hollywood Ruled The Skies - Volumes 1 through 4 by Bruce Oriss


Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Previous topic | Next topic 
Author Message
Phil Earthey
PostPosted: Thu Apr 12, 2007 4:40 pm 
Offline

Joined: Fri May 07, 2004 3:40 am
Posts: 54
Location: Norwich, UK
We're after induction trunking for a Mustang, the ducting that runs under the engine. Also after a few other parts, as follows:

Windscreen Frame
Oil Cooler
Elevator and Rudder balance weights
Elevator trim tabs
Rudder and Elevator trim jacks
Engine mount and parts

Any ideas most welcome. Have tried the usual suspects but am drawing a blank.

Thanks,

Phil
Top
 Profile  
 
Bill Greenwood
 Post subject: Spifire valve
PostPosted: Thu Apr 12, 2007 6:20 pm 
Offline
Probationary Member

Joined: Wed Jun 21, 2006 7:53 pm
Posts: 3803
Location: Aspen, CO
Sorry meant that as a PM.

_________________
Bill Greenwood
Spitfire N308WK


Last edited by Bill Greenwood on Thu Apr 12, 2007 9:14 pm, edited 1 time in total.

Top
 Profile  
 
Gary Norville
 Post subject:
PostPosted: Thu Apr 12, 2007 6:40 pm 
Offline

Joined: Sat Apr 02, 2005 10:13 am
Posts: 92
Hi,

Call Jay Wisler at Warbird Parts in Tampa FL (813) 968 5048 for ALL your warbird needs.

Carl Scholl at Aero Trader in Chino CA. was making induction trunks from scratch.

I'm sure Glenn Wegman of Fighter Enterprises will leave a post, he has rebuilt our trim actuators to factory standards along with other system parts.

We (American Aero) are building aluminum tabs for our two current projects.

Good Luck

Gary Norville
American Aero Services
333 South Street
New Smyrna Beach, FL. 32168
386-423-7700
Top
 Profile  
 
Lynn Allen
 Post subject:
PostPosted: Thu Apr 12, 2007 9:33 pm 
Offline
3000+ Post Club
3000+ Post Club
User avatar

Joined: Fri May 07, 2004 10:10 pm
Posts: 4404
Location: Maypearl, Texas
Nelson Ezell can make anything out of metal for any aircraft :wink:

www.ezellaviation.com

Lynn
Top
 Profile  
 
Yak 11 Fan
 Post subject:
PostPosted: Fri Apr 13, 2007 5:59 am 
Offline
User avatar

Joined: Tue May 04, 2004 2:53 pm
Posts: 299
Location: UK
I take it you have had a chat with the man up the road Phil? If not I can tomorrow. I know he doesn't have those part but may be able to give you some ideas.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » General Discussion » The WIX Hangar

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 45 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB® Forum Software © phpBB Group