Warbird Information Exchange
https://www.warbirdinformationexchange.org/phpBB3/

Conquest 1 build on youtube
https://www.warbirdinformationexchange.org/phpBB3/viewtopic.php?f=15&t=71817		 Page 1 of 1
Author:  JimH [ Sat May 23, 2020 4:58 am ]
Post subject:  Conquest 1 build on youtube
Getting more nerdy, but this is fun to put together. This is the High Planes 1/48th scale Conquest 1, American Jet. Great little kit! If all goes well it will be 5 parts, 1-2 are completed, 3 will go up tomorrow night.

jim

https://youtu.be/9N_j79aP3SA

https://youtu.be/8xeHLFhFKD4
Author:  JimH [ Sun May 24, 2020 8:03 pm ]
Post subject:  Re: Conquest 1 build on youtube
Here is part 3...fun project...may do a few more as time permits. This is the meat of the build

Jim

https://youtu.be/uM1W5z2P4LE
Author:  JimH [ Sat Jun 06, 2020 5:24 pm ]
Post subject:  Re: Conquest 1 build on youtube
part 4 is up...painting and the tedious but beautiful decals. The decals didn't age well and broke in to many pieces as they went on. Lots of water and micro sol got them all back together.

Jim

https://youtu.be/s-_sp9ptcJY
Author:  Snake45 [ Sat Jun 06, 2020 5:29 pm ]
Post subject:  Re: Conquest 1 build on youtube
JimH wrote:
part 4 is up...painting and the tedious but beautiful decals. The decals didn't age well and broke in to many pieces as they went on. Lots of water and micro sol got them all back together.

Jim

https://youtu.be/s-_sp9ptcJY

Age has nothing to do with it. They did the same thing on the one I built almost 20 years ago, when that kit was brand new. Never seen decals that needed a coat of Micro Superfilm more.

https://modelingmadness.com/review/civil/mesnerf8f.htm
Author:  JimH [ Sun Jun 07, 2020 1:57 am ]
Post subject:  Re: Conquest 1 build on youtube
That's an interesting read...it's like re-living this entire build. I really like the kit and knew it was going to be a lot of work from the time I opened the box. I have the Smirnoff version as well...those big blue decals will be a nightmare. For all its faults its much easier than modifying a Testors or similar kit.

Jim



Snake45 wrote:
JimH wrote:
part 4 is up...painting and the tedious but beautiful decals. The decals didn't age well and broke in to many pieces as they went on. Lots of water and micro sol got them all back together.

Jim

https://youtu.be/s-_sp9ptcJY

Age has nothing to do with it. They did the same thing on the one I built almost 20 years ago, when that kit was brand new. Never seen decals that needed a coat of Micro Superfilm more.

https://modelingmadness.com/review/civil/mesnerf8f.htm
Author:  Snake45 [ Sun Jun 07, 2020 7:26 am ]
Post subject:  Re: Conquest 1 build on youtube
JimH wrote:
That's an interesting read...it's like re-living this entire build. I really like the kit and knew it was going to be a lot of work from the time I opened the box. I have the Smirnoff version as well...those big blue decals will be a nightmare. For all its faults its much easier than modifying a Testors or similar kit.

Jim

I reread it last night myself, and was surprised I didn't have nightmares last night. :shock:

If I HAD to build another one, I would--as I suggested in the review--buy the HP kit, then use it as a "conversion set" and transplant all the Conquest I specific parts onto a HobbycraftAcademy kit (including the cowling--the HP Bearcat has THE most accurately shaped cowling of any of the 1/48 Bearcat kits). The basic HP airframe is just TOO much of a PITA to get together. (I now know that the Hawk/Testor kit is so inaccurate in so many areas that it's worth building these days ONLY as a "fun with nostalgia" exercise.)

The decals were beautifully printed, though, even if horrid to work with.

Good luck with yours! :drink3:
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/