| Warbird Information Exchange https://www.warbirdinformationexchange.org/phpBB3/ |
|
| 1/32 F4-U and P-38 https://www.warbirdinformationexchange.org/phpBB3/viewtopic.php?f=15&t=5068 |
Page 1 of 1 |
| Author: | oscardeuce [ Fri Sep 30, 2005 10:04 am ] |
| Post subject: | 1/32 F4-U and P-38 |
|
|
|
| Author: | TimAPNY [ Fri Sep 30, 2005 12:42 pm ] |
| Post subject: | |
Very nice. Makes me want to start my project kits. |
|
| Author: | CWBuff [ Fri Sep 30, 2005 6:00 pm ] |
| Post subject: | |
Like that Corsair. That's the Trumpeter kit, yes? The P-38 looks like the old Revell kit... did you use Eduard stuff in the cockpit? Fade to Black... |
|
| Author: | oscardeuce [ Sat Oct 01, 2005 9:46 pm ] |
| Post subject: | |
Yes, the new Trumpeter U bird with some Waldron placards. The 38 is the old Revell with BMF and the Waldron kit. |
|
| Author: | TimAPNY [ Mon Oct 03, 2005 7:03 am ] |
| Post subject: | |
The cockpits, are those the "detail Sets" that you can buy for your models? If so, or for those who have used them, are they worth it and how do they fit with the A/C model. Do they need to be the same brand? |
|
| Author: | oscardeuce [ Mon Oct 03, 2005 5:46 pm ] |
| Post subject: | |
P-38 Waldron cockpit set. Very good, but very time consuming. I would say youneed to be at least an advanced modeler to attempt. Lots of little parts and special tools needed. F4-U Stock Trumpeter cockpit with the Waldron Corsair cockpit placard set. P-38 kit was about $28, F4-U was about $9 |
|
| Author: | tom d. friedman [ Mon Oct 03, 2005 6:35 pm ] |
| Post subject: | |
meticulous detail!!!! i envy your talent!!! i also envy your time . i've got 20 + kits better than 10 years old staring me in the face. if i could find the time i'd get back into it, but that's not the case. i'm considering selling all my models, tools, accessories etc. i've got quite a bit tied up in the tools, dental tools etc. since 1995 all doing me no good   regards, tom
|
|
| Author: | CorsairFreak [ Mon Oct 03, 2005 6:47 pm ] |
| Post subject: | |
If you ever consider selling your stuff, PM me. I might be intrested. |
|
| Author: | mrhenniger [ Tue Oct 04, 2005 6:36 am ] |
| Post subject: | |
oscardeuce wrote: P-38 Waldron cockpit set. Very good, but very time consuming. I would say youneed to be at least an advanced modeler to attempt. Lots of little parts and special tools needed.
Hmmmm..... I hope to get back to my 1:24 Hobby Craft/Trumpeter P-51D as winter sets in. I bought a Waldron set for it as well. Here is the thing... this is my first model since I was a kid. Yikes. I would appreciate anything you could share in terms of techniques and tools. Think of my as a dry sponge wait to soak any useful info. TIA Mike |
|
| Author: | oscardeuce [ Wed Oct 05, 2005 10:04 am ] |
| Post subject: | |
Did you buy the Waldron punch and die set? You will need one. A lighted magnifying glass will help alot to. There are (obviously lots of 3D parts to make out of 2D foil. Lots of bending and cutting. A good set of hemostats and smaller needle nose pliers will help with the bending. A good CA glue will be needed. The directions are a bit vague at times and alot of trial and error is needed to complete the set. I worked on it for months, and it still has areas that I can improve on. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|