Oil Board Stencils Source

L-4Pilot · **Joined:** Tue Jan 18, 2011 10:35 pm **Posts:** 616

I need a set of stencils cut for the T-41B and do not want to use vinyl masks. We will use vinyl for the star and bar etc but not for the 1/4 and 1/2 inch stencils. I could not find the information from the last L-19 I did ten years ago. and would appreciate a reference to someone who can do a good job for us.

Thanks

N3Njeff · **Posted:** Thu Sep 18, 2014 12:19 pm

Ive done some stencils for folks here.............. got a 1/2, 3/4 and 1" Marsh machines

N3Njeff · **Posted:** Thu Sep 18, 2014 12:24 pm

PM now sent

C VEICH · **Joined:** Sun Nov 15, 2009 12:40 pm **Posts:** 1455

I did some a while back for a fellow here at WIX working on a T-6 restoration. I cut them with a laser cutter and thus am not limited to specific sizes. I am, however, somewhat limited in overall size so it may be a matter of puzzling stencils together if they are large. If Jeff can't do what you need I would be more than happy to discuss it.

L-4Pilot · **Joined:** Tue Jan 18, 2011 10:35 pm **Posts:** 616

N3Njeff wrote:

PM now sent

Thanks Jeff, I just emailed the Tech Manual pages that show the stencils that I need in 1/2 and 1 inch. I have taken care of the 1/4 inch interior stencils. There is one other stencil that I need two of that is not listed in the tech manual and it is for the door release. Attached is a photo of that 1/2 inch stencil, these are on the lower kick panels immediately in front of the door posts and are sprayed on the vinyl panels.

Thanks Again,
Steve

L-4Pilot · **Joined:** Tue Jan 18, 2011 10:35 pm **Posts:** 616

[quote="C VEICH"]I did some a while back for a fellow here at WIX working on a T-6 restoration. I cut them with a laser cutter and thus am not limited to specific sizes. I am, however, somewhat limited in overall size so it may be a matter of puzzling stencils together if they are large. If Jeff can't do what you need I would be more than happy to discuss it.[/quote

Thank you

Ken · **Posted:** Tue Feb 17, 2015 3:07 pm

C VEICH wrote:

I did some a while back for a fellow here at WIX working on a T-6 restoration. I cut them with a laser cutter and thus am not limited to specific sizes. I am, however, somewhat limited in overall size so it may be a matter of puzzling stencils together if they are large. If Jeff can't do what you need I would be more than happy to discuss it.

I might need 3" or 4" stencils. Font to match USAF, late Vietnam. Museum project ... info to follow in a separate thread.

Ken

p51 · **Posted:** Tue Feb 17, 2015 4:05 pm

Rick Larsen does a great job, you normally just need to tell him what you're looking for. I've used him in the past and he always does top-knotch stuff: http://www.militarystencils.com/

C VEICH · **Joined:** Sun Nov 15, 2009 12:40 pm **Posts:** 1455

Ken wrote:

C VEICH wrote:

I did some a while back for a fellow here at WIX working on a T-6 restoration. I cut them with a laser cutter and thus am not limited to specific sizes. I am, however, somewhat limited in overall size so it may be a matter of puzzling stencils together if they are large. If Jeff can't do what you need I would be more than happy to discuss it.

I might need 3" or 4" stencils. Font to match USAF, late Vietnam. Museum project ... info to follow in a separate thread.

Ken

Hi Ken,

No problem with 3"-4" letters and I can custom make them to match whatever documentation you provide. The only issue would be my schedule which is very heavy at the moment. If you don't need them in a huge rush I would be happy to have a look. Shoot me an email at cwveich@cwvmodels.com if you would like to discuss the details.

Chad Veich

L-4Pilot · **Joined:** Tue Jan 18, 2011 10:35 pm **Posts:** 616

I am very pleased with the stencils Jeff did for me. They are clean and crisp, have never seen better,

Steve

Warbird Information Exchange

Oil Board Stencils Source

Who is online